A537 Сталь

en10025 s235jrg1

en10025 s235jrg1

en10025 s235jrg1

040A12 JIS G3131 BS 970-1 040A12 NF EN10025 S185 BS

BS970Partl BS EN10025 BS970Partl BS EN10025 080A15 S235JR S235JRG1 stainless steel Bar Foreign trade department:Dongguan Pulin Metal Co., Ltd. was established in year 2005. We have been exporting a wide range of metal inclusive of stainless steel, aluminium, alloy, copper and many more products to worldwide market like North and South America BalkanSteelStandard:Steel Grades:Wire Rod:EN10025:S235JR, S235JRG1 , S235JRG2, S275JR, S355J0:BDS2592:St1 to St4 (kp, ps, sp) - group A, B, W:DIN17100:S137-2, US137-2

EN 1.0038 Steel S235JR Material Equivalent, Properties

S235JR Material Introduction. EN 10025 S235JR material (1.0038 steel) is an European standard hot rolled non-alloy structural steel grade. It has good plasticity, toughness and weldability, certain strength and good cold bending properties. EN 10025 :1993 - Leong HuatNotes :1) FU = rimming steel, FN = rimming steel not permitted, FF = fully killed steel, opt = at manufacturers option. 2) It is permissible to exceed the specified values provided that for each increase of 0.001% N the P content is reduced by 0.005%; the N of the ladle analysis shall not however exceed 0.012%. 3) The max value for N does not apply if the analysis shows a minimum total EN10025 S235J2G4 steel - Shanghai Katalor Enterprises Co., S235J2G4 is a kind of carbon structural steel under the standard EN10025. S235J2G4 carbon steel requires the min yield strength is 235Mpa.J2 in EN 10025 S235J2G4 steel refers to the material also should have minus 20 degrees Celsius, the impact toughness of v-notch impact test bar power to reach above 27 joules. G4 in S235J2G4 refers to Super killed steel.

S235JR Steel Plates

EN10025-4:2004:1.8834:440 to 630:430 to 590:355:345:335:325:325:320:22-20C:40J:S460ML:EN10025-4:2004:1.8838:500 to 680:490 to 660:460:440:430:410:400:385:17-20C:40J:This table provides the main features of the mechanical properties of different offshore grades as required by the relevant standards. It is not complete as Structural Steel - S235, S275, S355 Chemical Composition May 11, 2012 · The naming convention used in European Standard EN10025 refers to the minimum yield strength of the steel grade tested at 16mm thick. Structural Steel Grade at 16mm. Minimum Yield Strength at nominal thickness 16mm. psi. N/mm 2 (MPa) S235. 33 000. 235 N/mm 2. S275. 36 000. 275 N/mm 2. S355. 50 000. What is EN 10025 Grade S235JR? - Matmatch

  • NamingProperties of S235jrApplicationsEN 10025 S235JR has a specified chemical composition of 0.17 – 0.20 wt.% carbon (depending on thickness), 1.40 wt.% manganese, 0.55 wt.% copper, 0.012 wt.% nitrogen, 0.04 wt.% phosphorous and 0.04 wt.% sulphur. Plate thickness has a major impact on elongation and yield strength. Elongation ranges from 26 % for plates less than 40 mm thick to 22% for plates thicker than 100 mm but thinner than 125 mm. Yield strength ranges between 360 and 510 MPa for plates less than 100 mm thick, and 350 EN10025 S235JRG1 Carbon steel round bar Size Tolerance EN10025 S235JRG1 Carbon steel round bar is used for engineering and structural carbon structural steel and low alloy structural steel, usually without heat treatment. S235JRG1 steel round bar is machinable with common operations such as cutting, grinding and welding.S235JRG1 steel is a kind of common carbon structural steel.

    s235jrg1, s235jrg1 Suppliers and Manufacturers at

    1,608 s235jrg1 products are offered for sale by suppliers on A wide variety of s235jrg1 options are available to you, There are 91 suppliers who sells s235jrg1 on , mainly located in Asia. The top countries of supplier is China, from which the percentage of s235jrg1 БалканСтийлTranslate this pageСтандарт:Марка стомана:Бетонно желязо:EN10025:S235JR, S235JRG1 , S235JRG2, S275JR, S355J0:BDS2592:St1 to St4 (kp, ps, sp 철강유사재질(철강)비교 :네이버 블로그Translate this page유첨 파일 참조해 주시고보다 많은 철강규격검색은 Http://sermet.kr 철강규격비교표(철강) 출처 :

    EN 10025-2 S235JRG1 steel plate - BEBON steel expert

    EN 10025-2 S235JRG1 steel plate is carbon and low alloy steel.EN 10025-2 S235JRG1 steel plate is machinable with common operations such as cutting, grinding and welding. EN 10025-2 S235JRG1 steel plate is used in riveted, bolted, or welded construction of bridges and buildings.

Свяжитесь с нами

Электронное письмо: [email protected]